Deleted
Registered: Dec 4, 2024 2:16:23 GMT -7
Posts: 0
|
Post by Deleted on Aug 6, 2013 18:46:26 GMT -7
It seems to be quite the task to get a good paint job using rattle cans. Does this get better with an airbrush, or is there some secret to using a rattle can successfully?
|
|
|
|
Post by CustomMuscle on Aug 7, 2013 4:09:05 GMT -7
I usually heat the can up by putting it in hot water for about 4 or 5 min. It creates more pressure and the paint will less likely orange peel on you. Practice on a junk body first to get an idea how it works. Also wipe the spray nos clean after each use or it will tend to spit paint out in little concentrated drops. I have used only rattle can for years. But been thinking about trying an airbrush Most guys say it's easier to get a good paint job and can get more detail.
|
|
Deleted
Registered: Dec 4, 2024 2:16:23 GMT -7
Posts: 0
|
Post by Deleted on Aug 7, 2013 5:33:48 GMT -7
I've used cans more than the airbrush. Like Custom said, warming up the can helps with the pressure a lot! The trick to cans is light coats and lots of patience. Depending on the type of paint you use, you should wait anywhere between 5 min - 4 hours between coats. If you let too much time pass you'll have to days for another coat. Also your preparation goes a long way. Sand the body before you spray primer. Sand the primer before you add paint.
Hands down an airbrush will give you better results but it takes sometimes more than twice the amount of time spent compared to cans. The end results are worth it though. Same thing with an airbrush, spray light coats. The paint will dry faster if your psi is set at the right level. Keep your airbrush super clean between jobs to keep it spraying just the way you want it to.
Hope this helps, gunslinger.
|
|
|
|
Post by Grandpabeast on Aug 7, 2013 19:43:21 GMT -7
I agree with all that has been said. I have been a big rattle can addict and with the right prep you can do good to great paint jobs even two tone and custom jobs. If your looking to get crazy and do a lot of fine detail painting nothing beats a airbrush.
|
|
Deleted
Registered: Dec 4, 2024 2:16:23 GMT -7
Posts: 0
|
Post by Deleted on Aug 8, 2013 16:45:12 GMT -7
I will have to agree with all of the above statements as well.
I have only painted with rattle cans, and my problem is all this humidity here in Texas. I have an electronic thermometer and check to make sure the humidity is low before I plan a paint job. I keep the paints outside along with the parts I am going to paint. Sanding takes time and patience, but the trick is to get the parts looking nice before you start the actual paint job. Sanding before you prime, after you prime, and between coats. Always keep the nozzle clean and do not let any buildup dry. Shake between sprays if possible. Never let the paint run out during a job because that last little bit will spatter and ruin a good job.
Take your time and be patient. You can achieve anything just as long as you have a plan and take time in the prep.
|
|
Deleted
Registered: Dec 4, 2024 2:16:23 GMT -7
Posts: 0
|
Post by Deleted on Aug 8, 2013 19:11:18 GMT -7
Hey jioliv, have you tried a dehydrator to dry your kits? I think that's what it's called. I've never used them myself, but from what I understand its supposed to help your kits dry faster. Just a thought.
Didn't mean to hijack the thread, gunslinger. I still think you should have both and practice, practice, practice!
|
|
Deleted
Registered: Dec 4, 2024 2:16:23 GMT -7
Posts: 0
|
Post by Deleted on Aug 9, 2013 8:39:06 GMT -7
I have looked into that in the past, but I have heard many stories of warping and the issue with temperature control. I did find a DIY build which uses light bulbs as a heat source and I think I will try that out. I am also looking into building my own paint booth because the problem is not so much drying; it's the high humidity affecting the paint job during the process. DIY Dehydrator |
|
Deleted
Registered: Dec 4, 2024 2:16:23 GMT -7
Posts: 0
|
Post by Deleted on Aug 9, 2013 17:04:28 GMT -7
I greatly appreciate all the tips!
|
|
Deleted
Registered: Dec 4, 2024 2:16:23 GMT -7
Posts: 0
|
Post by Deleted on Jan 8, 2018 3:01:49 GMT -7
I usually heat the can up by putting it in hot water for about 4 or 5 min. It creates more pressure and the paint will less likely orange peel on you. Practice on a junk body first to get an idea how it works. Also wipe the spray nos clean after each use or it will tend to spit paint out in little concentrated drops. I have used only rattle can for years. But been thinking about trying an airbrush Most guys say it's easier to get a good paint job and can get more detail.I i was never any good with the cans. i bough a compressor and gun it takes getting use to but its a much cleaner spray with way more control |
|
|
|
Post by jkflash on Jan 8, 2018 10:39:16 GMT -7
I don't claim to be an artist by any means, but when I spray models I typically use rattlecans. I have an old inexpensive airbrush that I never could get to work right. But with the proper prep work you can do a lot with rattlecans.
|
|
